Wall-mounting. For ground mounting please see prewired perimeter tower model S20xxx.

Features:

Each reference includes a central body in aluminium, a polycarbonate profile, top/bottom covers and also an anti-sabotage tamper switch, as many heaters as photoelectric sensors (transmitters or receivers), a thermostat and a motherboard that manages the system.

Everything is prewired and mounted together with the IR beams – (*) chosen by the customer – and their mounting back plates.

(*)  Compatible with different models of photoelectric beams (TAKEX, OPTEX, ATSUMI and others). These are not included in price. easyPack can also be supplied without photoelectric beams.

This perimeter tower is ready for wall-mounting.

Additionally as an option, you can acquire other accessories for easyPack prewired beam towers such as fans and/or power supplies as well as other usual Bunker’s beam towers’ accessories (anti-climb top tamper, etc.). For more information see “Accessories” paragraph.

Most common models for 2m height and 180º:

• W202RR – 2m, 180° wall-mounting tower ready for 2 Rx.
• W202TT – 2m, 180° wall-mounting tower ready for 2 Tx.
• W203RR – 2m, 180° wall-mounting tower ready for 3 Rx.
• W203TT – 2m, 180° wall-mounting tower ready for 3 Tx.

(Tx = transmitter/s; Rx= receiver/s)

For other configurations, please consult us.

The post easyPack prewired beam towers – 180°, 2m, wall installation appeared first on Bunker Seguridad Electrónica S.L..

Ground mounting. For wall-mounting please see prewired perimeter tower model W20xxx.

Features:

Each reference includes a central body in aluminium, a polycarbonate profile, top/bottom covers and also an anti-sabotage tamper switch, as many heaters as photoelectric sensors (transmitters or receivers), a thermostat and a motherboard that manages the system.

Everything is prewired and mounted together with the IR beams (*), chosen by the customer and their mounting back plates.

(*) Compatible with different models of photoelectric beams (TAKEX, OPTEX, ATSUMI and others). These are not included in price. easyPack can also be supplied without photoelectric beams.

It also includes side brackets.

Additionally as an option, you can acquire other accessories for easyPack prewired beam towers such as fans and/or power supplies as well as other usual Bunker’s beam towers’ accessories (anti-climb top tamper, 0,70m steel side brackets, floor bracket to be used in combination with concrete, etc.). For more information see “Accessories” section.

Most common models for 2m height and 180º:

• S202RR – 2m, 180° tower ready for 2 Rx.
• S202TT – 2m, 180° tower ready for 2 Tx.
• S203RR – 2m, 180° tower ready for 3 Rx.
• S203TT – 2m, 180° tower ready for 3 Tx.

(Tx = transmitter/s; Rx= receiver/s)

For other configurations, please consult us.

The post easyPack prewired beam towers – 180°, 2m, ground installation appeared first on Bunker Seguridad Electrónica S.L..

Given that Bunker manufactures a wide range of perimeter products for solely residential areas, such as Garden Guard (MALTA, CAV and CAV-W), we refer to the MB-W infrared tower with the adjective “industrial”, even though in real situations both MB IR towers (180º) and PT (360º) security towers are installed very often in residential areas and they integrate perfectly their stylish design in the environment.

Features:
All the MB-W single-sided infrared tower models (180º) for perimeter security protection include the following components:

• Black polycarbonate profile which allows the infrared rays, emitted by the photoelectric beam, to go through.
• Black anodized aluminium profile which forms part of the IR tower structure, curved on the rear side.
• Two anti-sabotage tampers to be fixed on the upper side of the IR tower and consequently avoid a possible manipulation of the perimeter security system by putting out of order a photoelectric sensor or even by cancelling an infrared photo beam.
• Installation kit: it is composed of stainless screws, used to fix an infrared tower to the wall, to fix infrared photo beams to the main part of the security tower, etc.

MB-W perimeter security infrared tower for wall use is provided with only one hole on the lower side of the IR tower, the installer must make another in order to be able to fix the infrared tower to the wall. The reason why is that this way the perimeter security installer can choose where in the perimeter tower to make the hole to consequently avoid the possibility the hole is seen in case the security tower is not 100% fixed to the wall.

As a manufacturer, Bunker gives the possibility to adapt infrared tower’s height in case none of our 180º MB-W infrared tower references covers your perimeter security system requirements.

The post MBW – Single-sided (180°) beam tower, wall mount appeared first on Bunker Seguridad Electrónica S.L..

Given that Bunker manufactures a wide range of perimeter products for solely residential areas, such as Garden Guard (MALTA, CAV and CAV-W), we refer to the MB infrared tower with the adjective “industrial”, even though in real situations both MB IR towers (180º) and PT security towers are installed very often in residential areas and they integrate perfectly their stylish design in the environment.

Features:
All the MB single-sided infrared tower models (180º) for perimeter security protection include the following components:

• Black polycarbonate profile which allows the infrared rays, emitted by the photoelectric beam, to go through.
• Black anodized aluminium profile which forms part of the IR tower structure, curved on the rear side.
• Anti-sabotage tamper to be fixed on the upper side of the IR tower and to consequently avoid a possible manipulation of the perimeter security system by putting out of order a photoelectric sensor or even by cancelling an infrared photo beam.
• Installation kit: it is composed of stainless screws, nylock nuts and expandable bolts.

In addition, 3m high infrared tower model (MB300), manufactured by Bunker Seguridad, is equipped with 70cm MB3SB side brackets. These give more stability to the infrared photo beams set inside, but also more rigidity to the electric tower which has an effect on the perimeter security system with less unwanted alarms.

– As a manufacturer, Bunker gives the possibility to adapt infrared tower’s height in case none of our 180º MB infrared tower references covers your perimeter security system requirements.

– Single-sided (180º) MB perimeter security tower models, manufactured by Bunker, are floor-installation models. If you wish to fix IR tower on a wall, it is necessary to use MB-W range of infrared towers for perimeter security.

– Single-sided (180º) MB is commercialised with minimum elements required to undertake an optimal photo beam perimeter security installation which does not need more accessories, nor extra fixations and in stable temperature ranges, without extremes. From here onwards, Bunker offers a wide range of accessories for our security towers which cover the majority of market requirements.

The post MB – Single-sided protection perimeter tower (180°) for infrared photoelectric beams appeared first on Bunker Seguridad Electrónica S.L..

Given that Bunker manufactures a wide range of perimeter products, such as Garden Guard (MALTA, CAV and CAV-W), for solely residential areas, we refer to the PT infrared tower with the adjective “industrial”, even though in real situations MB IR towers (180º) and PT security towers are installed very often in residential areas and they integrate perfectly their stylish design in the environment, also when using PT-LUX and PT-CCTV accessories (the first one transforms the perimeter security tower into a lamp as low consumption bulbs can be fixed to it. As for PT-CCTV, it allows to integrate inside the infrared tower (AIR) up to two CCTV cameras, which makes the solution very compact and clean. Please see “Accessories” paragraph for more information.

Features:

• Two black polycarbonate profiles which allow the infrared rays, emitted by the photoelectric beam, to go through.
• A black anodized aluminium profile which forms part of the IR tower structure.
• An anti-sabotage tamper to be fixed on the upper side of the IR tower and to consequently avoid a possible manipulation of the perimeter security system by putting out of order a photoelectric sensor or even by cancelling an infrared photo beam.
• Installation kit: it is composed of stainless screws, used to fix an infrared tower to the floor, to fix infrared photo beams to the main part of the security tower, etc.

In addition, 3m high infrared tower model (PT300), manufactured by Bunker Seguridad, is equipped with 70 cm MB3SB side brackets. These give more stability to the infrared photo beams set inside, but also more rigidity to the electric tower which has an effect on the perimeter security system with less unwanted alarms.

The post PT – Double-sided protection perimeter tower (360°) for photoelectric beams appeared first on Bunker Seguridad Electrónica S.L..

Ground mounting. For wall-mounting the accessory PTWB is required.

Features:

Each reference includes a central body in aluminium, two polycarbonate profiles, top/bottom covers and also an anti-sabotage tamper switch, as many heaters as photoelectric sensors (transmitters or receivers), thermostat and the motherboard that manages all the system.

Everything is prewired and mounted together with the IR beams (*) – chosen by the customer – and their mounting back plates.

(*) Compatible with different models of photoelectric beams (TAKEX, OPTEX, ATSUMI and others). These are not included in the price. easyPack can also be supplied without photoelectric beams.

Additionally, as an option, you can acquire other accessories for easyPack prewired beam towers such as fans and/or power supplies as well as other usual Bunker’s beam towers’ accessories (anti-climb top tamper, 0,70m steel side brackets, concrete floor bracket, etc.). For more information see “Accessories” section.

Most common models for 2m height:

• D204RR – 2m, 360° tower ready for 2 Rx on each side.
• D204TT – 2m, 360° tower ready for 2 Tx on each side.
• D204TR – 2m, 360° tower ready for 2 Tx on one side and 2 Rx on the other side.
• D206RR – 2m, 360° tower ready for 3 Rx on each side.
• D206TT – 2m, 360° tower ready for 3 Tx on each side.
• D206TR – 2m, 360° tower ready for 3 Tx on one side and 3 Rx on the other side.

(Tx = transmitter/s; Rx= receiver/s)

For other configurations, please consult us.

The post easyPack prewired beam towers – 360°, 2m, ground installation appeared first on Bunker Seguridad Electrónica S.L..